How to replace the LED downlight
The installation of downlight in the ceiling is an essential part of the whole household lighting. Generally, we will predict the number of downlight devices when installing the ceiling, as well as the direct device spacing between downlight and downlight. The selection of downlight interval can refer to other articles for solution, and then is the opening device. However, the downlight device is not damaged once the tube is installed How to replace the lamp when it is broken, and how to disassemble and repair the LED spotlight in the living room?
1. Prepare the LED downlight to replace and repair the things needed. Generally, the common things to replace and repair the LED downlight are: electric tape, a set of LED downlight of the same model, pliers, and a small hand saw if necessary.
2. Turn off the power and buckle the lamp slowly. Pay attention to the spring clip on the lamp. After seeing it, press it down with your finger to take out the lamp. If you don't pay attention to the spring clip, you will be hurt by the spring clip if you pull down the lamp head, so be careful to remove the old broken led downlight.
3. Then take apart the connector and replace the lamp holder. If the driver does not move, turn on the light switch. If the light is not on, it can be determined that it is the driver fault and replace the driver.
4. Turn off the light switch at the moment. It is suggested to turn off the main power supply, and then turn on the power input line of the driver (it can also be cut short directly). Then remove the broken driver, and then peel the new power input section of the driver, and peel the two light wires.
5. Wrap one of the driver power lines around the lamp power cord (the lighting power is not positive or negative), and stick it with electric tape. The other one is connected with the same method and wrapped with electric tape.
6. It will be over. Next, power on the experiment, turn on the switch and the light will be on. If it is not on, repeat the above process, but directly replace the LED downlight instead of the driver!
Source: Bihua Lighting Appliance Factory, Henglan Town, Zhongshan City http://www.zsbihualed.com
-
09-15
What is the difference between LED downlight and LED spotlight
What's the difference between LED downlights and led spotlights? In home decoration, led downlights and led spotlights are used more. On the one hand, they are needed for auxiliary lighting lamps such as LED downlights and led spotlights. On the other hand, led downlights and led spotlights are not limited by decoration styles. Basically, each decoration style is suitable for LED downlights and led spotlights. All kinds of styles can be taken into consideration. Not only that, led downlights and
-
09-15
The difference between LED ceiling lamp and LED panel lamp
Led ceiling lamp is generally installed in the interior of the room. The appearance design of the lamp is that the upper part is flat, and it is installed close to the roof, like adsorbing on the roof, so it is called led ceiling lamp. The LED panel lights are more diversified, including horizontal LED panel lights, embedded LED panel lights, ceiling LED panel lights, hanging LED panel lights, circular LED panel downlights, and circular ceiling LED panel downlights. As the ceiling mounted panel
-
09-15
Three purchase directions of LED wall lamp
In fact, the wall lamp is a kind of lamp which plays an important role in home decoration. Wall lamp can make your home glow with unique brilliance. At present, led wall lamp is used at most. The light of LED wall lamp is elegant and harmonious. It can decorate the whole environment with elegance and high profile. It can make home play the role of finishing point and add different aesthetic experience. This shows that led wall lamp is also very necessary to install, so the premise of installatio
-
09-15
How to solve the problem of heat dissipation for LED panel lamp?
In the LED panel lamp, there are three basic stages of heat transfer, from integrated chip to epitaxy, from packaging base steel plate to heat sink or shell. At present, the technical problem of LED heat dissipation is that led nodes are limited by temperature. High temperature will cause led integrated chip, luminous powder, packaging epoxy resin service life is reduced. In order to keep the advantages of high efficiency and long life of LED, the junction temperature of LED must be controlled.